2018 Ford F150 Lariat - Walkaround, Review
Additional Options. Tachometer; Spoiler; CD player; Navigation System; Air Conditioning; Traction control; AM/FM radio: SiriusXM; Fully automatic headlights ; Tilt steering wheel; Speed-sensing steering; Illuminated entry; Radio: HD Sony AM/FM Stereo/CD Player/MP3 Capable; Steering wheel mounted audio controls . Step-by-step instructions guide you through the process of removal of the factory radio unit and replacement of factory speakers. This was very helpful . Ford F Crutchfield Customer Review (What's this?) Great instruction, made specifically for my vehicle. Pros: Exactly what I needed! Cons: None! 0 of 2 found this. Save on Headlamps, Headlights & Parts with great deals at Advance Auto Parts. Buy online, pick up in-store in 30 minutes.
How To - Adding lights to interior light circuit. Page 1 of 2. There have been a few threads on this topic, and this weekend I got around to adding step lights to my running boards. Get access to the factory wiring route to under the truck.
This is for those adding lights to the running boards or to the bed of the truck 1.
How To - Adding lights to interior light circuit - Fonline Forums
Remove the sill plate cover. I used a plastic trim tool, I would strongly suggest getting a set if you are doing any amount of work on your truck. Several places on line have them. Even a plastic putty knife from HD or the likes is better then the screw driver in a rag method Start from one end, and work you way to the other.
3 MUST HAVE F150 UPGRADES FOR UNDER $29.99 FOR YOUR 2015-2016 FORD
There are 3 spring clips holding this down. All the way off, you can see where the spring clips and alignment clips are at in this picture 2. Remove the door seal so you can take the kick panel out, to access the interior lighting circuit 3.
Remove the kick panel driver's side The access cover around the hood latch need to be removed. I just pulled the center back, to release the clips top and bottom. This made the piece convex shaped, and the clips released the clips were narrower then the opening The kick panel is held in Aiken Dating Site Video 2018 F-150 Headlight Bulb by 2 springs clips, a locating pin on the kick panel, and a slide tab of sorts in the center. Pull the kick panel towards the rear of the truck to release the spring clips, and slide forward to clear the locating pin and tab in the center of the panel Spring clips, locating pin, and center mounting tab.
Finding the Interior circuit in Connector C 4. One is towards the outside of the truck, one is towards the inside of the truck.
Circuit 53 is towards the outside of the truck. The way I found to trace the wires, is to cut the C cover taped to the wiring loom and following the wire up. To go here access to the Connector cover, remove the hood latch by unbolting it, and sliding it off the A-pillar.
This is where I added the inline Tap for connection to the fuse, and on to the added LED step lights. If you are adding more then a few LEDs, then this would be used for triggering a coil on a relay. The access to under the truck is located under the carpeting on the driver's side. The plastic on the floor is for the floor mat mount, as a reference point to where this is located. I just poked through the grommet with an awl, and pulled the wires back up into the truck. Hope this helps with some trying a similar project.
Find all posts by Screw-Me Thanks for the write up! Find all posts by john Going to move this one down to the How-To Forum! Find all posts by Rockpick. Find all posts by kankles Thanks much for the detailed description of adding lights to the interior more info circuit.
I was able to easily follow them when adding in floor lights. Appreciate the great info! Find all posts by bgilcher.
Find all posts by Raptor Dude, You're the "Real Deal". Keep up the good work. This information is exactly what I've been looking for. Find all posts by Fifty Hey sscully, There wouldn't happen to be an equal wire running down the passenger side too would there?
I don't think that is a good choice for MH's. The company tried to tell us he retired, and even put a positive spin on it, but only some of us knew what was really going on. Find all posts by Barricade. Professional Parts Sweden 6. By far the Best "LED" lighting replacement available.
If doing lights on both ends how would you suggest powering the pass side? Find all posts by RemyRed. I went under the dash, down the passenger side kick panel by the fuse panel, and under the truck in the door sill.
SMS Supercars was the continuation of Mr. Page 3 of 4. I guess I could look at the dome light wire and see if it follows down through the cable tray along the driver's door. I'm very happy for Steve and the family. The fog lights are useful for lighting the on a wider arc even when it is not foggy.
I wanted a single fuse for the running board entry lamps, so this was a no brainer for me. I've gotta do this mod on my new Anyone know which wire color and location I could use? I guess I could look at the dome light wire and see if it follows down through the cable tray along the driver's door. Find all posts by aikenpearlbb. The late production MY had a connector in the driver's side kick panel for the Interior lighting that looks like it would do the trick for you.
This is the Gray with Violet stripe wire going to Front Dome lamps.
The other place would be the passenger side kick panel, in Connector CA, pin 2 for the output to the cargo lamps, White Wire. Think I have short in dome light.
Explore Nissan Motor Company, Nissan Qashqai, and more!
Thread Tools Show Printable Version. Add a Poll to this Thread.
You may not post new threads. BB code is On. All times are GMT The time now is We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.